Household shredder for plastic. Do-it-yourself plastic crusher - drafting and assembling home-made equipment. Types of crushers

If other than impeccable build quality and high performance, you are also interested in an affordable price, a plastic shredder from company "Stankopolimer"- that's exactly what you need. Our company supplies equipment for polymer processing own production. For the assembly of our installations, we use only high quality components, many of which, such as knives and augers, our company manufactures independently.

Rich choice is the key to consumer success

The company produces several models of shredders, each of which is designed to work with certain types of plastic raw materials:

• more suitable for processing thick waste single rotor shredder;
• better for recycling plastic bags buy a two-shaft shredder.

Also in our assortment you will find universal installations.

We offer the most diverse equipment on the market, including solid waste granulation and sorting lines. Please contact us if you need a plastic crusher or any other equipment used in the process of processing plastic, film and other types of polymeric materials.

The shredder includes:

A plastic shredder is a plastic crushing plant (it also crushes wood, tires, pipes, solid waste, etc.). Shredders for plastics are produced with a tangible margin of strength and wear resistance. With the help of its design, it is able to work with raw material of predetermined dimensions.

• loading compartment (window);
• spinning rotor with knives;
• sieve (installed depending on the task set by the client).

Plastic of any strength is processed until it is sifted through a sieve placed under the rotor. There are also other models of shredders with multiple rotors.

The knives on the rotor have four very sharp blades (after working out, the knife is turned over with a different edge and fixed again, due to this, the life of the knife increases).

Installation selection

Choosing the right shredder for shredding plastic will help the characteristic that you should pay attention to:

• engine power;
• the speed of the circular motion of the rotor (measured in the number of revolutions per minute);
• loading window size;
• blade width and type.

From the above, it depends on what types and dimensions of plastic the shredder will be able to crush.

Types of plastic shredding plant

There are the following types of shredder:

• single-rotor, which grinds bulky waste of various shapes from plastic, rubber, wood;
• double-rotor, unlike single-rotor crushes thick-walled waste (thick-walled plastic pipes, car tires) of the same shape.

Plastic shredding equipment must be installed on a perfectly flat surface, otherwise the correct operation will be impaired. Any unevenness on the surface leads to vibration of the equipment, which will adversely affect its performance. In addition, our company offers plastcompactors at affordable prices.

You can buy a plastic shredder on the website of the Stankopolimer company, where the best plants of various models are provided that meet any needs of industrial enterprises that process plastics.

You can also buy a shredder for plastic, the price of which will satisfy each client, by calling the number listed on the site.

They have firmly entered modern life, and there is not a single industry where they would not be used, from the production of containers to space technologies. Every year, about 180 million tons of various plastics are produced on the planet. Most of them cannot decompose on their own into simple components and self-dispose of.

This brings irreparable damage to nature and can cause an ecological catastrophe. A positive feature of almost any polymer (plastic) is the possibility, thanks to which old plastic things can get a “new life” as useful items. Recycled plastic is slightly inferior in terms of strength characteristics to the primary polymer, but with certain proportions, products made from recycled plastic practically do not differ from the original.

Varieties of choppers

Before being recycled, any plastic must be shredded. For this, there are special devices - crushers. Depending on the physical qualities of the polymer placed in them, the devices can be classified into several categories:

• for shredding PVC film, nylon or acrylic. The design resembles large scissors with "V"-shaped blades;
• for large plastic waste. Most often used in recycling plants or plastics factories. There are hammer, jaw or cone designs. With their help, window profiles and large parts and cases are crushed;
• for PET bottles and thin-walled plastics. The most common version of the grinder, structurally called rotary.

The required type of apparatus can be purchased or made by yourself. This is a small household appliance from the third category. Do-it-yourself plastic crusher is quite easy to do and does not require serious knowledge and specialized tools, except for a welding machine.

Learn more about rotary shredder

The most common design is the impact crusher. It consists of a rotor on which the knives are fixedly fixed. Under the action of a driving force - from a diesel, gasoline engine or an electric motor, the axis with knives sets in motion and grinds the raw materials that have fallen under the knives with quick blows. Depending on the purpose, there are low-speed machines and high-speed units.

At the bottom of the working chamber, a sieve or grate with a certain mesh size is installed, depending on the required quality and diameter of the obtained fraction. Raw materials are cyclically processed by knives and gradually pass through a sieve.

Particular attention is paid to the quality of the metal from which the knives are made - it must be a good hardened steel, which prevents rapid wear and ensures that sharpening is maintained for a long time.

We make our own crusher

There are several of the most popular types of shredders that are made at home. In order to assemble this device with your own hands, you will need a little patience and minimal skills. As a special tool, you only need a welding machine or a household inverter.

A do-it-yourself plastic crusher, the scheme of which will differ slightly depending on the skill level of the manufacturer and his imagination, has the following common elements:

• drive unit. The most commonly used electric motor. Thanks to a large selection and affordable prices, you can choose the model of the required power. In addition, the electric drive crusher is quieter and can be used both outdoors and indoors;
• circular saws. This will be the basis of our apparatus. It is necessary to select a sufficient number of them and a different configuration of teeth for better grinding of waste. The optimal number of saws on the axis is about 20;
• the axis on which the saws will be attached;
• metal profile or pipe for the manufacture of the support frame and frame of the crusher;
• protective cover and feed hopper. They can be made independently at home from galvanized sheet metal with metal scissors, a hammer and a vice;
• a pulley, two bearings and a special belt, with which an interaction is created between the electric motor and the rotor;
• fasteners (nuts, washers and self-tapping screws for metal).

When all the necessary materials and tools are prepared, you can begin to manufacture the unit.

First of all, you need to build a cutting block. To do this, we put circular saws on the prepared axle. The diameter of the axle and the seat of the saw must match. There should be a minimum distance between improvised knives, which is provided by ordinary metal washers. At the ends of the saw should be well fixed with nuts. Then we install the axle on the pulley and use two bearings so that the structure rotates freely.

The next step is the manufacture of the supporting frame. We make a rectangular frame from a metal corner, profile or pipe by welding. Then we weld the legs of the required height to it. We cover the frame with a sheet of metal, which is welded to the frame. We cut a hole in the sheet equal to the size of the cutting block. We mount the engine at a short distance from the knives.

After the frame is ready, you can proceed to the final stage of assembling our device. To do this, we put a protective cover on the knives and install a hopper on top for supplying raw materials. A hole must be provided in the casing through which the axle will be connected to the pulley. Using a special belt, we connect the motor shaft and the cutting block. Our simplest plastic crusher design is ready.

People who have extensive experience in the manufacture of various units with their own hands recommend that they first draw up a drawing of the future design. In this way, you can avoid size mismatches or miss a node or part.

Before purchasing an engine, you should decide on its power and output speed. For infrequent use and at low loads, a compact electric motor of low power is sufficient. The more actively the crusher will be used, the more powerful and “resourceful” the motor should be.

Circular saws are better to choose light-alloy ones. They are slightly more expensive than standard products, but they retain their sharpness much better, which will save you from regularly and often removing the cutting block to sharpen saws. The design itself should be thought out in such a way that you can easily get to any of its nodes.

For greater convenience, you can make a special container where the processed raw materials will be located. The container is fixed directly under the saws of the crusher. If you need to receive recycled plastic of various sizes, you should take care of manufacturing and installing a special grid or grid under the disks with the desired cell size.

Small Conclusions

A plastic crusher is a tool that will not only help fight environmental pollution, but also bring some income to the owner. Shredded plastic can be handed over by weight to recycling points and earn some money. In addition, depending on the design of the cutting unit and the power of the motor, the device can be used to grind leaves and branches - and this is already a serious help to any summer resident or owner of a private house.

The assembly of the unit is not particularly difficult, and thanks to your own developments, you can improve the design. self-assembled crusher will not differ in any way from mass-produced shredders for household needs, and in terms of reliability it will surpass cheap Chinese counterparts. One of the options for what a plastic crusher can be - a video story is attached.

Throughout life, we have to deal with different polymers. They have been used for the past few decades for the manufacture of a wide variety of products, from plastic containers to parts for space construction. In just one year on the planet produced about 180 million tons of plastic for various purposes.

A significant part of them is occupied by polymers that do not decompose and are unable to independently be disposed of. All this cannot but affect the ecological situation and often leads to ecological disasters. But the processing of polymers is not such a technologically difficult task. Moreover, on their basis, you can make useful things. Recycled plastic is virtually indistinguishable from virgin polymer and has almost the same performance characteristics.

Types of crushers

The whole variety of plastic recycling devices can be represented in the form of several groups according to the purpose and design of the main working elements.

Depending on the device and application, plastic waste crushers are of the following types:

• Crushers-shredders of plastic of great thickness and strength, reminiscent of body-type elements and window profiles in execution.
• Waste shredders of small thickness, designed for the processing of bottles and other items, in the design of which cascade-type shredders act as the main working unit.
• Cutters for plastic film waste, which work on the same principle as conventional scissors.

With a closer study of the device of plastic shredders, among their many options, plastic shredders can be distinguished, designed to process certain types of polymer waste:

• Impact crushers for plastics. It is this type of shredders that are most often used for recycling plastic waste. Available in two versions - high-speed for shredding fragile products and low-speed, designed for the disposal of durable plastic products.
• Crushers equipped with a roller material feed mechanism.
• Cone devices in which the process of utilization of raw materials occurs by passing it between two cones.
• Hammer devices. Designed for the processing of hard plastics. All the work in them is performed by hinged hammers.
• Cheek aggregates. Waste is disposed of by exerting pressure on the raw material with corrugated steel plates.

The best way to handle the task of recycling thick polymers is low-speed devices with a power of about 10 kW. At the same time, they easily process the most durable, thick types of waste, even without pre-treatment. It is not uncommon for low speed crushers to be used for the first coarse crushing step. At the next stages, high-speed units are already used. Such a combined approach to the utilization of raw materials increases the overall performance of the crushing complex to the required levels.

Destined for recycling polymers equipment is produced by both Russian manufacturers and foreign companies. Quite a lot of aggregates for crushing plastic are presented from Chinese manufacturers, which can not only be purchased at attractive prices (not higher than 250 thousand rubles), but also have good performance and high reliability.

Scope of application

The main users of plastic shredders are:

• Organizations engaged in the manufacture of polymer products.
• Companies whose activities include the collection and subsequent disposal of secondary raw materials.
• Manufacturing enterprises engaged in the production of plastic items for various purposes.

As a result of the processing of defective products, as well as other types of industrial plastic waste, a continuous supply of recycled plastic is ensured, from which new goods with the necessary consumer properties can be made. properties. The process of reusing defective products and recyclable materials allows manufacturing enterprises to save considerable amounts of money on the manufacture of plastic products. This reduces the cost of finished products.

Organizations involved in the recycling of used plastic products cooperate directly with companies that are direct manufacturers polymer products. Therefore, the sale of recycled plastics can bring a very significant profit to the enterprise.

The principle of operation of crushers for plastic

Secondary plastic raw materials, which are most often presented in the form of bottles and film fragments, have a heterogeneous composition, which requires the use of various processing methods. After all, these wastes can have different strength characteristics, viscosity and brittleness.

Despite the fact that it is not difficult to cut film waste, it is crushed using impact crushers practically unrealistic. Particularly laborious in this regard is ABS plastic, which has high rates of thickness and strength, which can only be crushed by sawing or impact.

In order to select the most suitable recycling method for recycled plastic, it is necessary to take into account its thickness. It is for this reason that each grinding apparatus must have such construction in order to process a certain type of secondary raw materials most efficiently and quickly.

Features of the shredder device for plastic recycling

Considering that today it is necessary to process waste from plastic for various purposes, in order to more effectively perform this task, enterprises should be equipped with shredders. certain design. There are many types of equipment, each of which is capable of processing plastic only in a certain way.

So, with a film that can be easily cut, even aggregates with a shock method of impact cannot cope. At the same time, ABS plastic is easy to recycle. drum kits. Due to the difference in the thickness of plastic products, enterprises have to use only a certain method of recycling for shredding each of them. This explains why every plastic recycling shredder must have certain performance characteristics.

To select the most suitable type of shredder, it is necessary to proceed from the type of plastic products that have arrived for processing and obtaining recycled plastic. Most shredders easily cope with the task of shredding film, plastic products of small thickness, as well as large plastic objects.

We make our own crusher

Owners who decide to assemble a plastic shredder on their own can find a lot of options for this useful device on the net and choose the most suitable one from them. Making this device with your own hands is not so difficult - you just need to be patient and have minimum skills work. It is possible to assemble a high-performance plastic processing unit without the use of special equipment. To perform the work, you only need a welding machine or a household inverter.

Tools

Each master can, at his own discretion, make changes to the scheme below, however, in any case, a home-made plastic crusher will include the following mandatory elements:

• Drive unit. Usually an electric motor is used as it. If you don’t have anything unnecessary, then you can go to the store and find there among the offered assortment an inexpensive model that has the necessary power. The crusher, equipped with an electric drive, is also advantageous in that it has a quieter running, so you can use it not only on the street, but also indoors.
• Circular Saw. It will be responsible for the recycling of plastic waste. Make sure that you have enough saws with different tooth shapes so that you can shred the waste efficiently. Given the task at hand, it is ideal if you install at least 20 saws on one axis.
• Working axis designed for mounting saws.
• A metal profile that can be replaced with a pipe of a suitable diameter. The support frame and the frame of the crusher will be made from it.
• Protective cover and feed hopper. For their manufacture, you can use galvanized sheet. You will also need a special tool - metal shears, a hammer and a vise.
• A pulley, a pair of bearings and a special belt that will maintain the interaction between the electric motor and the rotor.
• Various types of fasteners - self-tapping screws for metal, washers and nuts.

crusher manufacturing

After you resolve the issue with materials and tools, you can proceed directly to the manufacturing process of the crusher.

The process begins with the manufacture of the cutting block. We take the axis and put circular saws on it. Please note that the seat of the saw must have the same diameter as the axle. Make sure there is enough space between the improvised knives to place metal washers. To ensure the reliability of fastening the saws, nuts must be put on the ends. After that, you can install the axle itself on the pulley. Two bearings must be put on it, then the structure will rotate freely.

At the next stage, we begin to make a supporting frame. We take a welding machine and make a rectangular frame using a metal corner, a profile or a pipe. Next, you need to weld the legs to it, having previously calculated their height. Directly to the frame lay the sheet metal and weld it to the frame. A hole must be made in the sheet, which must be the same size as the cutting block. Now you can install the engine, which we place near the knives.

After the work on the manufacture of the frame is completed, we proceed to the final stage of assembling the chopper. We take a protective cover, put it on the knives, and attach a hopper on top, through which raw materials for grinding will be supplied. Do not forget to make a hole in the casing for the subsequent connection of the axle with the pulley. Next, wear special belt, which will connect the motor shaft to the cutting block. On this, the work on making a crusher for plastic with your own hands can be considered completed.

So that the plastic crusher does not cause you problems during operation, experts recommend drawing up a drawing at the very beginning, which will allow you to get a visual idea of ​​\u200b\u200bwhat your homemade shredder will look like. This will allow in the future to avoid gross miscalculations and inconsistencies in the sizes of individual nodes.

When you decide on the choice of an electric motor, you first need to understand how often you are going to use the crusher. For a device that will be subjected to infrequent and minor loads, a low-power power drive will suffice. If you intend to actively exploit it, then you should look for a more powerful power unit with a large number of revolutions.

Summing up

Considering the sheer volume of polymer products used by mankind, it is not surprising that interest in devices such as the plastic shredder has grown in recent years. The main purpose of this device is to recycle plastic waste, which can later be reused to make new things that, in terms of their performance, will practically not differ from the original ones.

Such units are now used not only in industry, but also in the domestic sphere. However, owners do not always decide to purchase such a device. Some have the idea to make it on their own. In fact, anyone with minimal skills in working with the tool can cope with this task. Although the risk of errors cannot be ruled out, if you thoroughly prepare for the assembly process and draw up a detailed diagram of the chopper, then in terms of its functionality it will not differ in any way from the branded unit.

Plastic recycling - one of the freest niches in Russia for doing business.

However, the question of opening it most often rests on the cost of equipment.

Often, entrepreneurs do not start with a full processing cycle with ready-made granulate at the output, but with the collection and grinding of polymer waste.

Even in this case, the purchase of a shredder and (or) crusher may not be affordable. One of the most discussed solutions to the problem is to make your own shredder.

Such projects are quite feasible if two "constant quantities" are known - raw materials and products.

Both types of equipment perform the same task - crushing.

When processing plastics This process is divided into two stages:

• coarse grinding - shredders are used for this;
• obtaining crumbs of a fine fraction - a crusher is used for this.

The principle of operation and kinematics of both units are most often the same, and they differ only in some details, for example, the size of the sieve mesh, the overlap of the knives and the configuration of the cutting edges.

The process is divided into two stages to improve performance and energy optimization.

The design of the shredder for plastics

When choosing a design for a plastic shredder, you should pay attention to the proposals of equipment manufacturers.

It is better to take other people's developments as a basis for the project and have certain guidelines than to reinvent the wheel and end up with a non-working model.

The most popular are single- and two-shaft shredders of the rotary type.

Single shaft

Single shaft shredders are used for initial shredding most types of polymers.

It consists of a rotor on which movable knives (2) are fixed and a housing with fixed or stator knives (1). The raw material is fed through the loading window from above, and the finished crumb is poured out under its own weight through a calibrating sieve (3).

The grinding process is a repeated cutting and continues until all the plastic goes into the receiving hopper.

Rotary blade configuration selected depending on the material being processed:

1. dovetail and oblique– for processing, and other soft waste.
2. Direct– for crushing sprues, boxes, thick-walled blown products, from PET bottles. Such knives are often made in the form of separate segments that are cascaded. Segmentation is performed to reduce shock loads on the drive, reduce noise and vibration.

Stator knives for single-shaft polymer crushers are made solid (type P).

twin-shaft

Rotor and stator knives on such crushers are staggered, and the shafts rotate in opposite directions.

Inefficient machines with a small working chamber are performed with a single drive, the teeth on the rotary knives are used to capture and crush waste.

Grinding is also carried out by the side surfaces (as in a circular shear).

Where can I get blueprints?

You need to understand that manufacturers of equipment for shredders and crushers won't post blueprints in open access.

The easiest way to get schemes for a homemade shredder or crusher is in two ways:

1. Read related forums, like this . The probability of finding accurate and detailed drawings of plastic shredders is very small. Often, resource users remake some unclaimed equipment from a related industry, for example, a lopper. And if the crusher is made from scratch, few people care about documenting all the stages of manufacturing. However, it's worth reading the forums: analysis of discussions and other people's mistakes designing will help to make a plastic shredder with your own hands for a more perfect model.
2. Remove dimensions from current grinder. It will not work to get complete information, since the owner will not allow disassembling a working machine. But even a visual assessment will help in making your own homemade crusher.

Many attempts to make a crusher on their own come to a standstill due to the fact that the designer is trying bind to an existing node. For example, "fit" all the elements under the worm gear found in the garage.

An attempt to reduce the cost of the design due to secondary parts, as a rule, leads to errors.

Initial data for design

It is better to start manufacturing with a clear definition of the tasks of the grinder, that is, you need to know the type and amount of processed raw materials, the size of the fraction at the output.

After that, we find a model of any well-known manufacturer suitable for these parameters and take its technical characteristics:

• engine power;
• loading window dimensions;
• number and diameter of rotors;
• knife configuration.

Drafting a project

For example, we determined that a two-shaft shredder with a low rotor speed is suitable for production tasks.

His project necessarily includes:

• choice of engine by power;
• calculation of the gear ratio of the gearbox and the choice of the factory model;
• determination of the diameter and length of the rotors (according to the size of the loading window);
• calculation of shafts for strength;
• choice of bearings.

You will need a textbook for this."Machine parts" for universities. You will also have to look into GOSTs for threaded connections, reference books on gearboxes, bearings, couplings and other assembly units.

When using hardware foreign production often inconsistencies arise standardization, for example, “their” retaining rings are thicker than “ours” with equal diameters.

This must be taken into account when assigning groove dimensions.

After calculations it is necessary perform knot layout on graph paper or in the AutoCAD type editor, determine the dimensions of body parts and bed.

This task must be approached responsibly so as not to miss anything. Sometimes the protruding head of an "unaccounted" bolt leads to the fact that car needs to be redone. After that, detailing is done - a drawing of each part separately.

Drive design

In factory crushing plants, two methods are used to transfer rotation from the engine to the gearbox:

1. direct drive(through the clutch). The transmission of torque is lossless, the design is compact. If you managed to pick up a ready-made gear motor, the dimensions and weight of the installation will be even less. However, in this case, it is necessary to provide for manual (and ideally automatic) reversal in case of jamming of the rotors.
2. Belting. Losses in efficiency and relatively high dimensions are compensated by a smooth start of the mechanism. When jammed, the shredder is only threatened by a broken or slipping belt.

The transmission of rotation between the rotors (in the case of using a single motor) is most often carried out through an open gear train. When designing, you need to be ready for its calculation. Most likely, gears will have to be ordered.

Knives

Finding the right knife configuration is easy.

Many manufacturers do not make this a secret.

Anyone interested can choose the appropriate profile and resize under your rotor, make the right number of teeth.

Knives will also have to be ordered from a waterjet, plasma or laser cutting company. After that, you will have to grind them in one size along the plane.

The same applies to fixed knives. Only for them you still have to think about how to attach to the body.

Most often, two through holes are drilled in the counter-knives on the sidewalls and pulled together with pins through the spacer bushings.

Another pair of blind threaded holes is made from the side of the body for bolting to it.

Another important issue is the material. This can be one of the spring (65G, 60S2, 65S2VA) or die (Kh12MF) steels. Anyway have to order also competent heat treatment with hardness control of each finished knife.

Shafts

The standard knife fit configuration for most manufacturers is hexagon. That is, the workpiece for the shaft can serve rolling profile, the ends of which are machined for bearings, gears, etc.

The optimal choice is steel 40, 45, 40X with improvement (hardening + high tempering).

Bearing units

You can use ready-made bearing units of a self-aligning design.

They "forgive" errors in the alignment of the holes, in which conventional radial bearings will overheat and overheat.

However, compared to conventional bearings the cost of such nodes is much higher.

In addition, the dimensions of their bodies often do not allow maintaining the required center distance between the rotors.

To avoid misalignment, the sidewalls of the crusher body are used as axle boxes. Landing holes are bored in a machine with a four-jaw spindle, folding the parts together.

If it is not possible to make a housing with coaxial holes, you can choose double-row spherical bearings that are suitable in terms of load capacity.

Rotors

One of the main requirements for rotors is the presence guaranteed clearance between the sides of the knives. Otherwise they will rub against each other, perhaps even jamming of the mechanism.

The width of the spacers should be larger. They also need to be sanded to the same size.

Particular attention should be paid to the axial adjustment.

Shafts must be designed to allow move the entire set of knives and bushings tenths of a millimeter and reliably fix it when the side clearance is uniform.

Most often, threaded parts are made on the shafts, and the position of the knives is fixed with nuts.

Assembly of finished nodes

For the structure to be repairable, body should not be welded.

It is better to make a bolted connection.

Then the chopper can be taken apart at any time for sharpening or replacing knives.

One of the common problems with rotating machinery is increased vibration.

To avoid this phenomenon, it is necessary to align the actuator, gearbox and motor, i.e., align their axes.

Another reason for vibration is imbalance(imbalance) rotors. To eliminate it, you need to balance.

Useful video

We offer you to watch a video on how to realize the idea of ​​​​a plastic recycling business using home-made equipment:

Conclusion

Were considered not all difficulties that you will encounter in the process of designing and assembling a plastic shredder.

It is possible to call the production independent only conditionally, since this requires a whole machine park, and some units have to be bought as an assembly. Whole the process can take months, and financial investments will be required in any case.

After the development of the project "on paper" it is worth calculating the economic efficiency of the event: sum up the costs of harvesting and processing, and then compare with the price of a "factory" shredder.

Those who already had experience in manufacturing shredders believe that the idea justifies itself in two cases: if there are no strict time limits, or if it is planned to start mass production of such units. For the tasks of practical recycling of plastic, it is usually easier to choose a ready-made model.

In contact with

It is profitable to buy a shredder for plastic and without a headache. Assembly, delivery, commissioning

For the processing of polymers, we suggest that you familiarize yourself with single-rotor and double-rotor shredders. Quality equipment from a good manufacturer - that's what everyone needs. And we will help you choose a shredder for plastic, buy and start using it.

• Why is a plastic shredder better than a crusher?

  The shredder works more efficiently and, most importantly, with less waste - it does not make a lot of noise and leaves no dust behind. In addition, the size of the pieces of plastic can be completely different - the chopper will cope with everything. The plastic shredder is very resistant to damage of any type - knives and other parts do not wear out for a very long time.

• Shredder types

  Shredders for plastics can be completely different - depending on the amount of material that is collected in your production, you can choose a shredder by size and technical characteristics. The capacity is written on the fraction at the outlet - for example, 50 mm, but the size of the hole can be changed, depending on your wishes and needs. In addition, our company offers film shredders.

Positive traits

Buy a shredder, in which plastic is recycled at no additional cost, from us, and you will receive a device:

• With a minimum amount of noise;
• Compact and convenient design;
• Ease of management;
• High-quality and reliable knives on the rotor;
• Economical costs - a minimum of electricity consumption and machine maintenance;
• The design of the working chamber is suitable for processing plastics of large and small sizes.
• Highly efficient performance;
• Good price and availability of all models and spare parts of interest in our warehouse in Moscow;
• The shredder can be configured for more convenient use, as well as depending on the working conditions that are optimized in your production.

Recycling polymers is not such a complicated technological process, if there is a room, specialists and a plastic shredder. Thanks to the correct observance of the technological process, in a minimum amount of time, it is possible to clean a large pile of garbage and get a new product necessary for the production of plastic goods.

• Where is the plastic shredder used?

  The main customers of the shredder for solid waste are small and large enterprises specializing in the manufacture of plastic products, companies that collect garbage for the purpose of subsequent disposal, enterprises whose activities are related to the production of plastic products.

  The process of recycling used plastic and rejecting it on high-quality equipment guarantees the following advantages:

  • high productivity of granules of a certain size and shape;
  • reduction in the cost of the output product;
  • increase in the number of sales;
  • savings on the cost of purchasing parts;
  • quick profit;
  • achieving financial independence.

  To fulfill your dream and develop a plastic recycling business, there is little left to do: buy a plastic shredder. How to find us, and what is needed for this, we suggest that you familiarize yourself in more detail.

• How to choose a pvd shredder?

  Choosing a high quality product is easy. To do this, you can get advice from our specialist or fill out an online application on the official website of the company. Having indicated the contact details, the requirements for the equipment, the managers will select the unit of the required quality as soon as possible. There are several types of shredders on the market. Knowing the final destination of the installation, the preliminary boot parameters, our specialists will never make a mistake.